Features and Benefits

• Highest Level of Operator Safety - features include: HSSD™ High Speed Solid-State load Discharge -to remove exposed voltages faster than passive resistor designs,  SFI™ Safety Fault Interrupt - shuts down output in as little as 50uS from detection,  TLSS™ Test Lead Safety Sense - continuously verifies that test leads are properly connected prior to and during HV and continuity testing,  Recessed start switch prevents inadvertent actuation, Dual Channel current measurement detects earth leakage faults
• High Power Output-  means better drive capability and increased test throughout.  With up to 50mA of current sourcing for AC & DC hipot the 950i Series gets heavy duty  jobs done fast - available 200mA drive tackles even tougher sourcing requirements
• Wide Range of built-in Voltage Capabilities - starting at 6KV AC/DC extending to 10KVAC and 11KVDC or up to 30KV RMS AC with external option
• The Fastest Hipot Testers available - Thanks to our Dual Coldfire® microprocessors combined with Dual DSPs to provide Ramp rates up to 50KV/second, dwell times as low as 20mS and overall test times as fast as  3mS in optional Flash mode
• Expansive Test Sequence Memory holds up to 100 tests with up to 100 steps per test.  Tests can be selected via front panel, RS232 or Digital I/O or with optional GPIB/Ethernet
• Ground Bond Test Capability available in three models with output currents from 100mA to  40Amps RMS and test times from 20mS to 1000 seconds or longer
• 4-Wire Milli-Ohmmeter Function provides fast, accurate 5 digit resistance measurements with resolution down to 100µΩ and range up to 100K ohms
• Built-in Phase Angle Measurement - allows the measurement and display of both resistive (in-phase) leakage current and reactive (out-of-phase) leakage current caused by capacitive coupling
• Multi-Dwell Functionality - permits dwells at different voltage levels without having to return to zero between test steps - dramatically simplifying advanced analysis of dielectric properties
• Ramp High/Dwell Low Current Limits - permits the user to set separate limits for the ramp and dwell providing faster ramp times and lower leakage test limits
• LAN/Ethernet, USB Print, RS232, Digital I/O & Scanner Control - All Standard Interfaces - Provides the highest level of test automation.  Full serial control and DI/O with remote start/stop, safety fault interrupt, test select & more
• High Voltage Scanner Control - up to 256 point switching capability can be handled via the standard VICL auxiliary control port.  Available scanners can route voltages up to 15KV and currents up to 40A for multi-point hipot and ground bond test requirements
• Dual Dimensional / Test Specific / Broadband Arc Detection. Where lesser testers allow you to set a single, global, amplitude only arc limit - the technologically advanced 950i Series utilizes time & amplitude based arc limits and uniquely applies them to each desired test
• Hard Copy Test Report, Ethernet and GPIB all available via optional interface card.  Host USB printer control port generates comprehensive test report at the touch of a button, LAN and GPIB ports offer robust industrial interface formats
• Pico-Amp Leakage Measurement insures that even the lowest leakage current levels are accurately detected and tera-ohm range IR readings are stable and precise
• Test Specific Fixture & Cable Compensation - Automatically calibrate out offset errors caused by lead resistance, fixture capacitance and leakage.  Compensation constants are stored with each test and can be updated with the touch of a button
• Multi-Mode IR - Insulation Resistance values up to one Tera-ohm can be obtained with precision in your choice of 3 IR test modes - end test on timer, end test on pass reading or fail reading. Choose either AC IR or DC IR to suit your measurement requirement
• Continuously Variable IR Test Voltage - Unlike most IR testers which limit you to 3 or 4 discrete test voltages, the 950i Series allows you to select the test voltage you need. Starting as low as 2V all the way to 6.5KV or 11KV in the higher voltage models
• Capacitance Test Modes - For AC & DC hipot and IR provide tightly controlled charge and discharge profiles for superior results on critical solar panel tests and other highly capacitive loads
• Light Weight Switching Power Supply Design - Reduces component count and internal heat rise while improving overall reliability.  Starting at only 18 lbs, 950i Series portability is a snap
• 400Hz AC Voltage Withstand Testing provides aviation frequency specific test results for a more effective analysis of dielectric properties on avionic components
• Solar Panel Testing Simplified - Designed with PV testing in mind, the 950i Series uses  pico-amp resolution to detect minute defects in solar cells while its HSSD High Speed Solid Discharge provides the industry's safest and fastest throughput rates
• 3 Year Extended Warranty* - Built-in reliability you can count on for years to come
• Safety Tested per EN 61010-1. EMC compliant to EN 61326-1