| MANUFACTURER |
MODEL |
DESCRIPTION |
| AEROWAVE |
28-1745/R |
WR28 45 degree Right-Hand Twist, 2 inches length |
| AEROWAVE |
28-1790 |
WR28 90 degree Twist Section, 1.5 inches length |
| AEROWAVE |
28-1845 |
WR28 45 degree E-Plane Bend |
| AEROWAVE |
28-3000/10 |
WR28 Directional Coupler. 10 dB coupling |
| AILTECH |
8096 |
WR28 Argon Gas Noise Source, 16.25 dB ENR, 26.5-38 GHz |
| ANDREW |
F028PA-0360B |
WR28 Jacketed Flexible Waveguide, 36 in.length, cover/choke*NEW* |
| ANDREW |
F028PB-0240KS |
WR28 Jacketed Flexible/ Twistable Waveguide, 24 in.,cov/ch *NEW* |
| ANRITSU |
26UA28 |
WR28 Precision Low Power Termination |
| APOLLO MICROWAVES |
17144 |
WR28 UG600 choke flange x 2.4mm(f) Adapter |
| AQRGUS ET |
1IW28-38-1 |
WR28 Isolator, 20 dB, 37-40 GHz, 1/2 inch insertion length |
| ARRA |
28-220B-06 |
WR28 Straight Section, 6 inches length, brass |
| ARRA |
28-720-90 |
WR28 Variable Phase Shifter, 0-90 degrees, uncalibrated drive, 2.38 inch length |
| ATLANTIC MICROWAVE |
AMC-1466 |
WR28 Orthomode Tee Adapter, UG599/U flanges on thru-line, 0.21 x 0.21 inch square waveguide on orthomode arm, 1 inch length, aluninum |
| ATM |
28-325B-40-6-6 |
WR28 Directional Coupler, 40 dB coupling, removable WR28 to 2.92mm(f) adapter on coupled port *NEW* |
| AVANTEK |
SW88-6751 |
WR28 Active Doubler, 13.25-20 GHz +10 dBm in/ 26.5-40 GHz +16 dBm out, 12V 100mA |
| BAYTRON |
3-28-300/10 |
WR28 Directional Coupler, 10 dB coupling, directivity >20 dB |
| BAYTRON |
3Ka-65 |
WR28 Pressurization Section, 2-1/2 in length, 0-30 PSI gage |
| BAYTRON |
3Ka-80/60 |
WR28 60 degree H-Plane Bend |
| CMT |
1062690 |
WR28 x 2.92mm male Adapter, incorporates mitre E Plane bend, 2.65 x 3.85 inch leg lengths *NEW* |
| CMT |
58P33762Y |
WR28 Straight Section, 72 inches. length, aluminum, cover/choke flanges |
| CMT |
AR28-3-1A1A-A |
WR28 3 dB Fixed Attenuator, 1 Watt maximum *NEW* |
| CMT |
AR28-6-1B1B-C |
WR28 6 dB Fixed Attenuator, 1 Watt maximum |
| CMT |
LPTS-28 |
WR28 Sliding Termination, uncalibrated drive with locking screw |
| CMT |
RA28-2.4-F-1A-A |
WR28 x 2.4mm(f) Adapter |
| CMT |
RA28-K-M-1A-A |
WR28 x 2.92mm(m) Adapter |
| CMT |
RAE28-K-M-1A-A |
WR28 x 2.92mm(m) End Launch Adapter |
| CMT |
RBC28-10-1A1A |
WR28 Directional Coupler, 10 dB coupling |
| CMT |
RBCCL28-2.4MM-F-40-1B1B-C |
WR28 Directional Coupler, 40 dB coupling, 2.4mm(f) coupled port, 5.5 inches length |
| CMT |
RCC28-2-20 |
WR28 3-Port Crossguide Coupler, 20 dB coupling *NEW* |
| CMT |
REB28-1A1A-1.5-1.5-A |
WR28 90 degree E-Plane Bend, 1.5 inch bend radius, aluminum |
| CMT |
RFG28-18-7B7B-HP |
WR28 Unjacketed Flexible Section, 18 inches length, brass |
| CMT |
RFG28-8-1A1A-HP |
WR28 Unjacketed Flexible Section, 8 inches length, aluminum *NEW* |
| CMT |
RHB28-1B2B-1.12 |
WR28 90 degree H-Plane Bend, brass, 1.12 inch bend radius |
| CMT |
RHB28-1B-8B |
WR28 90 degree H-Plane Bend, 1 inch bend radius, cover/choke flanges, brass |
| CMT |
RS28-1A-!A-3.0-A |
WR28 Straight Section, 3 inches length, aluminum |
| CMT |
RS28-1A1A-4.0-A |
WR28 Straight section, 4 inches length, aluminum |
| CMT |
RS28-1A1A-6.0-A |
WR28 Straight Section, 6 inches length, aluminum *NEW* |
| CMT |
RS28-1A1A-8.0-A |
WR28 Straight Section, 8 inches length, aluminum *NEW* |
| CMT |
RS28-1A-1A-9.00-A |
WR28 Straight Section, 9 inches length, aluminum |
| CMT |
RS28-1B1B-6.0-C |
WR28 Straight Section, 6 inches length, brass |
| CMT |
WR28 74.38" |
WR28 Straight Section, 6 ft. 2-3/8 inch length, aluminum, cover/choke flanges |
| DEMORNAY BONARDI |
DBD-825/DB-820 |
WR28 Slotted Line, with carriage and detector |
| DEMORNAY BONARDI |
DBD-915 |
WR28 Variable Phase Shifter, 0-180 degrees, uncalibrated drive |
| DEMORNAY BONARDI |
DBD-969 |
WR28 Sliding Short, uncalibrated drive |
| DEMORNAY BONARDI |
DBD-969-1 |
WR28 Sliding Short, micrometer read |
| DIAMOND ANTENNA |
1145 |
WR28 Rotary Joint, L-shape, 26.5-38.0 GHz, cover/choke flanges |
| DORADO INTL. |
4IWN-39.2 |
WR28 Isolator, 20 dB, 38.7-40 GHz, 1/2 inch insertion length |
| DORADO INTL. |
BE-28 |
WR28 90 degree E-Plane Bend |
| DORADO INTL. |
BH-28 |
WR28 90 degree H-Plane Bend |
| DORADO INTL. |
DCG-28-10 |
WR28 Directional Coupler, 10 dB coupling |
| DORADO INTL. |
FT-28 |
WR28 Low Power Termination, 1 Watt maximum |
| DORADO INTL. |
HPT-28 |
WR28 Shunt (H-Plane) Tee. 2 inches length |
| DORADO INTL. |
S-28-F |
WR28 Straight Section, 5.87 inches length, gold flashed brass |
| DORADO INTL. |
TW-28 |
WR28 90 degree Twist Section, 2.96 inches length |
| DORADO INTL. |
WR28 HYBRID TEE |
WR28 Hybrid Tee, common port is SMA female |
| EIP |
2010404-02 |
WR28 Remote Sensor, for EIP Frequency Counter, 26.5-40 GHz |
| EIP |
2030022 |
WR28 Remote Sensor for EIP Frequency Counter, 26.5-40 GHz |
| ELMIKA |
DC108/1E-6 |
WR28 Directional Coupler, 6 dB coupling, 27-32 GHz, split block design, 6 inches length |
| EMERSON & CUMMINGS |
757D-E |
WR28 90 degree E-Plane Bend, choke flanges |
| EPSILON LAMBDA |
JL25-28 |
WR28 Standard Gain Horn, 25 dBi gain mid-band |
| FERROCOM |
031-339888 |
WR28 Circulator, 20 dB isolation, 36.8-40 GHz |
| FLANN MICROWAVE |
22081-30 |
WR28 Fixed Attenuator, 30 dB |
| FLANN MICROWAVE |
22110 |
WR28 Precision Direct Reading Attenuator, 0-60 dB |
| FLANN MICROWAVE |
22410 |
WR28 H-Plane Tee |
| FLANN MICROWAVE |
2242 |
WR28 E-Plane (Series) Tee, 2-1/4 inch length |
| FLANN MICROWAVE |
22441-8.25" |
WR28 Straight Section, 8.25 inches length *NEW* |
| FXR/MICROLAB |
U155AF |
WR28 Direct Reading Variable Attenuator, 0.5-20 dB |
| FXR/MICROLAB |
U175AF-25 |
WR28 Flat Broadband Attenuator, 25 dB, 1 Watt average |
| FXR/MICROLAB |
U206CF |
WR28 Tunable Detector, positive polarity, 1N53 diode, BNC(f) output |
| FXR/MICROLAB |
U312BF |
WR28 E-H Plane Tuner, micrometer drives |
| FXR/MICROLAB |
U501AF |
WR28 Low Power Termination, 1/2 Watt maximum, 1.05 VSWR |
| FXR/MICROLAB |
U510D |
WR28 Standard Mismatch, VSWR 1.20, 300 mW maximum |
| FXR/MICROLAB |
U610A |
WR28 Standard Mismatch, VSWR=1.00 |
| FXR/MICROLAB |
U610B |
WR28 Standard Mismatch, VSWR=1.05 |
| FXR/MICROLAB |
U622AF |
WR28 Hybrid Tee |
| FXR/MICROLAB |
U623BDF |
WR28 90 degree E-Plane Bend |
| FXR/MICROLAB |
U630CF |
WR28 Adjustable Short, micrometer drive |
| FXR/MICROLAB |
WF-0085 |
WR28 High Power Load, 75 Watts average/ 100 kW peak |
| GAMMA-F |
L-28256 |
WR28 38 GHz High Pass Filter, 2.25 inches length |
| GENERAL ELECTRIC |
7437764 |
WR28 x WR90 Taper Section, 2.3 inches length, aluminum |
| GENERAL MICROWAVE |
A420C |
WR28 Power Sensor, for General Microwave power meters |
| GENERIC |
31 GHz isol |
WR28 Junction Isolator, 20 dB, 31.0-31.5 GHz, 0.75 inch insertion length |
| GENERIC |
WR28 38 GHz BPFL |
WR28 Band Pass Filter, 35.5-40.0 GHz, 0.98 inch length |
| GENERIC |
WR28 4" straight |
WR28 Straight Section, 4 inches length, brass |
| GENERIC |
WR28 4.5" flex |
WR28 Unjacketed Flexible Waveguide Section, 4.5 in. length, brass |
| GENERIC |
WR28 4.5" straight (ch) |
WR28 Straight Section, 4.5 inches length, aluminum,choke flanges |
| GENERIC |
WR28 6" straight |
WR28 Straight Section, 6 inches length, aluminum, choke flanges |
| GENERIC |
WR28 7" straight |
WR28 Straight Section, 7 inches length, brass |
| GENERIC |
WR28 8 dB atten. |
WR28 Fixed Attenuator, 8 dB, 3 inches length |
| GENERIC |
WR28 8.88" |
WR28 Straight Section, 8.88 inches length, brass, cover/choke flanges |
| GENERIC |
WR28 bulkhead |
WR28 Bulkhead Adapter, UG600/U coke flanges both sides, on circular 2 inch diameter 8-hole flange, 0.3 inch thick, aluminum |
| GENERIC |
WR28 bulkhead |
WR28 Feedthrough Bulkhead, 0.7 inch length, mounted on a 1.38 x 0.75 inch tab, gold flashed |
| GENERIC |
WR28 CONICAL HORN |
WR28 Conical Horn Antenna, 1.2 inch cone length x 0.80 inch aperture |
| GENERIC |
WR28 CONICAL HORN |
WR28 Conical Horn Antenna, 1.5 inch cone length x 0.80 inch aperture |
| GENERIC |
WR28 E 90 mitre |
WR28 90 degree E-Plane Mitre Bend, 2-1/2 inch legs, aluminum |
| GENERIC |
WR28 E bend |
WR28 Assymetrical 90 degree E-Plane Bend, 1.55 x 1.05 inch legs, choke/choke flanges, silver plated brass |
| GENERIC |
WR28 H 90 mitre |
WR28 90 degree H-Plane Mitre Bend, 2-1/2 inch legs, aluminum |
| GENERIC |
WR28 twist |
WR28 90 degree Twist Section, 4.60 inches length, cover/choke flanges |
| GENERIC |
WR28 x WR42 |
WR28 x WR42 Taper Section, 3.4 inches length |
| GHZ MICROWAVE |
200143-12B |
WR28 Band Pass Filter, 38.588-38.888 GHz, 1.5 inch length |
| GHZ MICROWAVE |
A8959 |
WR28 28.2 GHz High Pass Filter, 1.1 inch length |
| GHZ MICROWAVE |
A9499 |
WR28 x 2.92mm(f) Adapter |
| GHZ MICROWAVE |
RM-170 |
WR28 x WR75 Waveguide Taper, 7.25 inches length |
| HITACHI |
R3601 |
WR28 3-Position 3-Port Manual Switch, H-Plane |
| HNL |
R219-10 |
WR28 Fixed Attenuator, 10 dB, brass, 4 inches length |
| HP/KEYSIGHT |
05356 |
WR28 x 2.92mm male End Launch Adapter |
| HP/KEYSIGHT |
11517A/19A/20A |
Waveguide Mixer Set, 18.0-40.0 GHz coverage, for HP 8555A, 8565A |
| HP/KEYSIGHT |
11970A |
WR28 Harmonic Mixer, 26.5-40 GHz, for use with Keysight analyzers |
| HP/KEYSIGHT |
11974A |
WR28 Preselected Mixer, 26.5-40 GHz, for HP spectrum analyzers |
| HP/KEYSIGHT |
83554A |
WR28 Source Module, +7 dBm levelled, for HP sources |
| HP/KEYSIGHT |
83572-60071 |
WR28 Directional Coupler, 10 dB coupling (same as R752C) |
| HP/KEYSIGHT |
R11644A |
WR28 Calibration Kit, for Agilent network analyzers |
| HP/KEYSIGHT |
R281A |
WR28 x 2.4mm(f) Adapter |
| HP/KEYSIGHT |
R281B |
WR28 x 2.4mm(m) Adapter |
| HP/KEYSIGHT |
R347B |
WR28 Noise Source, 12 dB ENR, 26.5-40 GHz |
| HP/KEYSIGHT |
R362A |
WR28 Low Pass Filter, 47 GHz (-30 dB) cutoff |
| HP/KEYSIGHT |
R365A |
WR28 Full Band Isolator, 25 dB isolation, 1.5 dB insertion loss |
| HP/KEYSIGHT |
R373D |
WR28 Precision Attenuator, 20 dB, 500 mW max., 1.05 VSWR, accuracy 0.7 dB + ripple 0.7 dB max. |
| HP/KEYSIGHT |
R373G |
WR28 Precision Attenuator, 50 dB, 500 mW max., 1.05 VSWR, accuracy 1.0 dB + ripple0.7 dB max. |
| HP/KEYSIGHT |
R375A |
WR28 Direct Reading Variable Attenuator, 0-20 dB |
| HP/KEYSIGHT |
R382A |
WR28 Precision Direct Reading Attenuator, 0-50 dB, 26.5-40 GHz |
| HP/KEYSIGHT |
R422A |
WR28 Broadband Crystal Detector, negative polarity |
| HP/KEYSIGHT |
R422A-002 |
WR28 Broadband Crystal Detector, negative, matched load |
| HP/KEYSIGHT |
R422C |
WR28 Broadband Crystal Detector, negative polarity |
| HP/KEYSIGHT |
R486A |
WR28 Thermistor Mount, for HP 432 series power meters |
| HP/KEYSIGHT |
R532A |
WR28 Direct Reading Frequency Meter, 0.11% accuracy |
| HP/KEYSIGHT |
R752A |
WR28 Directional Coupler, 3 dB coupling |
| HP/KEYSIGHT |
R752C |
WR28 Directional Coupler, 10 dB coupling |
| HP/KEYSIGHT |
R752CS |
WR28 Directional Coupler, 10 dB coupling, split block construction |
| HP/KEYSIGHT |
R752D |
WR28 Directional Coupler, 20 dB coupling |
| HP/KEYSIGHT |
R815B/814A/446B |
WR28 Slotted Line, with carriage and detector |
| HP/KEYSIGHT |
R8486A |
WR28 Power Sensor, -30 to +20 dBm, 26.5-40 GHz |
| HP/KEYSIGHT |
R8486D |
WR28 Power Sensor, -70 to -20 dBm, 26.5-40 GHz |
| HP/KEYSIGHT |
R85026A |
WR28 Detector, for HP 8757 series scalar network analyzer |
| HP/KEYSIGHT |
R870A |
WR28 Slide Screw Tuner, micrometer horizontal drive, uncalibrated probe drive |
| HP/KEYSIGHT |
R899A |
WR28 Straight Section, 2.5cm length |
| HP/KEYSIGHT |
R899B |
WR28 Straight Section, 5 cm length |
| HP/KEYSIGHT |
R899D |
WR28 Straight Section, 20cm length |
| HP/KEYSIGHT |
R910A |
WR28 Low Power Termination, 1 Watt maximum, 1.025 VSWR |
| HP/KEYSIGHT |
R914B |
WR28 Moving Load, 500 mW, 1.01 VSWR, uncalibrated drive |
| HP/KEYSIGHT |
R914C |
WR28 Moving Load, 500 mW, 1.01 VSWR, micrometer drive |
| HP/KEYSIGHT |
R920B |
WR28 Adjustable Short, micrometer drive |
| HP/KEYSIGHT |
WR28 9.85" |
WR28 Straight Section, 9.85 inches length |
| HUGHES |
45111H-2000 |
WR28 Full Band Isolator, 25 dB isolation, 1.5 dB insertion loss |
| HUGHES |
45141H-2000 |
WR28 Junction Isolator, 20 dB isolation, 35-37 GHz |
| HUGHES |
45161H-2000 |
WR28 Circulator, 20 dB isolation, 28.5-31.5 GHz |
| HUGHES |
45321H-2110 |
WR28 Directional Coupler, 10 dB coupling |
| HUGHES |
45321H-2210 |
WR28 Directional Coupler, 10 dB coupling; split block construction |
| HUGHES |
45321H-2310 |
WR28 Directional Coupler, 10 dB coupling; split block construction |
| HUGHES |
45421H-2290 |
WR28 90 degree H-Plane Bend |
| HUGHES |
45661H-2200 |
WR28 tunable load, micrometer read |
| HUGHES |
45711H-2000 |
WR28 Direct Reading Frequency Meter, 26.5-40 GHz |
| HUGHES |
45731H-2000 |
WR28 Variable Attenuator, 0-25 dB, micrometer read |
| HUGHES |
45751H-2000 |
WR28 Precision Direct Reading Phase Shifter, 0-360 degrees |
| HUGHES |
47121H |
WR28 IMPATT Sweep Osc., 27.5-28.4 GHz, +7 dBm, 42-44V drive, 120-180mA sweep current |
| HUGHES |
47341H-2100 |
WR28 Tunable Single Ended Harmonic Mixer, 26.5-40 GHz |
| HUGHES |
47431H-2003 |
WR28 Tunable Harmonic Mixer, RF=26.5-40G, LO=8-15G, IF=10-1000M |
| HUGHES |
47741H-2310 |
WR28 Phase-Locked Gunn Osc., 31.84-32.24 GHz, +19 dBm Po |
| HUGHES |
WR28 dual IMPATT osc. |
WR28 Dual IMPATT Osc., 34.3 GHz 100 mW & 37.4 GHz 50 mW, combined in a magic tee, isolator on output |
| HUGHRS |
45321H-1310 |
Round (UG381/U) flange WR28 Directional Coupler, 10 dB coupling, split block construction |
| JUNCTION DEVICES |
173RI |
WR28 Isolator, 20 dB, 37.2-39.4 GHz |
| KWM |
24DRI-3 |
WR28 Isolator, 20 dB, 37-40 GHz, 1/2 inch insertion length |
| LAMBDA MICROWAVE |
286.402.218-P |
WR28 Straight Section, 2.3 inches length, brass *NEW* |
| LIECO |
19M2 |
WR28 Medium Power Load, 50 Watts average power, UG600/U choke flange |
| LORCH MICROWAVE |
5WR28-29175/150 |
WR28 Band Pass Filter, 29.10-29.25 GHz, 3 inches length |
| LORCH MICROWAVE |
6WR28-31G/R60C |
WR28 Bandpass Filter, 30.9-31.1 GHz, 3-1/16" length |
| LORCH MICROWAVE |
7WG-39475/R350 |
WR28 Band Pass Filter, 39.30-39.65 GHz, 2-1/8 inches length |
| LORCH MICROWAVE |
7WR=28225/250 |
WR28 Band Pass Filter, 28.10-28.35 GHz, 3 inches length, cover/choke flange |
| M/A-COM |
093-449954-012A |
WR28 Fixed Tuned Gunn Oscillator, 38.90 GHz, +15 dBm Po, +4.4V 1.11A, with attached CMC junction isolator |
| M/A-COM |
093-449954-012B |
WR28 Fixed Tuned Gunn Oscillator, 38.87 GHz, +19.5 dBm, +4.5V 980mA, with attached CMC junction isolator |
| M/A-COM |
093-449954-106 |
WR28 Fixed Tuned Gunn Oscillator, 35.60 GHz, +13 dBm, +5.0V 440mA, with attached CMC junction isolator |
| M/A-COM |
3-28-150A |
WR28 Low Power Termination, 1 Watt, 1.05 VSWR |
| M/A-COM |
3-28-400/10 |
WR28 Directional Coupler, 10 dB coupling |
| M/A-COM |
3-28-422/20/20 |
WR28 Dual Directional Coupler, 20 dB coupling, 6 inches length |
| M/A-COM |
3-28-670 |
WR28 90 degree Twist Section, 2 inches length |
| M/A-COM |
4-28-720-02 |
WR28 Broadband Detector, negative polarity |
| MAURY MICROWAVE |
U233A1 |
WR28 x 2.92mm(f) End Launch Adapter, 1.10 VSWR |
| MAURY MICROWAVE |
U233B |
WR28 x 2.92mm male End Launch adapter, 1.25 VSWR |
| MAURY MICROWAVE |
U236A6 |
WR28 x 2.4mm Male Adapter, VSWR<1.15 |
| MAURY MICROWAVE |
U237A1 |
WR28 x 2.4mm Female End Launch Adapter, VSWR<1.10 |
| MAURY MICROWAVE |
U320D |
WR28 Standard Mismatch, 1.20 VSWR |
| MAURY MICROWAVE |
U351 |
WR28 5-Probe Tuner, matches 1.10 VSWR to <1.01, vernier drives |
| MDC |
66028-001 |
WR28 Straight Section, 12 inches length, aluminum |
| MDL |
25 dB ATTEN. |
WR28 25 dB Fixed Attenuator, 3.5 inch length with integral 90 degree H-Plane Bend |
| MDL |
28AC206 |
WR28 x 2.92mm(f) Adapter |
| MDL |
28AC39 |
WR28 x SMA(m) Adapter |
| MDL |
28EU16-1F |
WR28 x WR42 Taper Section, 2 inches length |
| MDL |
28WU119 |
WR28 Straight Section, 9 inches length, brass |
| MDL |
58028-449A |
WR28 Isolator, 20 dB isolation, 28.0-29.5 GHz |
| MDT |
5618 |
WR28 Isolator, 20 dB, 37-40 GHz, 1/2 inch insertion length |
| MDT |
MFMKu2A |
WR28 Doubler, 15.5-15.8 GHz +27 dBm in, 31-31.6 GHz +20 dBm out |
| MICRORECH |
239792-3 |
WR28 Unjacketed Flexible Waveguide Section, 4 inches length, aluminum |
| MICROTECH |
217864 |
WR28 Jacketed Twistable-Flexible Section, 4.125 inches length |
| MICROTECH |
2347831 |
WR28 38.6 GHz High Pass Filter, 4 inches length |
| MICROTECH |
239792-5 |
WR28 Unjacketed Flexible Waveguide Section, 5.5 inch length, aluminum |
| MICROTECH |
3400002-0001 |
WR28 Unjacketed Flexible Waveguide Section, 5 in. length *NEW* |
| MICROTECH |
3400003-0004 |
WR28 Unjacketed Flexible Waveguide Section, 4 in.length,aluminum *NEW* |
| MICROTECH |
3400003-0005 |
WR28 Unjacketed Flexible Waveguide Section, 5.5 in. length, aluminum *NEW* |
| MICROTECH |
MTPS28-PGC-N-24B |
WR28 Flexible/Twistable Jacketed Waveguide, 24 inches length, cover/choke flanges |
| MICROWAVE ASSOC. |
576S |
WR28 Fixed Attenuator, 6 dB, 31-36 GHz, 1 watt max. |
| MICROWAVE ASSOC. |
MA-539C |
WR28 Tunable Detector Mount, pos.polarity, micrometer read drive |
| MICROWAVE ASSOC. |
MA-560A |
WR28 Series (E-Plane) Tee. 2.38 inches insertion length |
| MICROWAVE ASSOCIATES |
1051 |
WR28 Rotary Joint, S-shape, 34.0-35.5 GHz, choke flanges |
| MICROWAVE DEEVELOPMENT CO. |
61028-001 |
WR28 Power Sampler, 30 dB coupling, 2.92mm(f) coupled port, 1.5 inch length |
| MICROWAVE DEVELOPMENT CO. |
51028-285 |
WR28 Short Body Directional Coupler, 6 dB coupling, directivity 20 dB, 5 inches length, cover/choke/choke flanges, aluminum |
| MICROWAVE DEVELOPMENT CO. |
65028-1462 |
WR28 90 degree E-Plane Bend, 1.2 inch radius bend, brass, cover/choke flanges *NEW* |
| MICROWAVE DEVELOPMENT CO. |
65028-1463 |
WR28 90 degree H-Plane Bend, 1.2 inch radius bend, brass, cover/choke flanges *NEW* |
| MICROWAVE RESEARCH |
A160-6 |
WR28 Directional Coupler, 6 dB coupling, 8.5 inches length |
| MICROWAVE SEMICONDUCTOR |
MC7350W |
WR28 Noise Source, 18 dB ENR, 34.7-35.3 GHz, 28VDC, BNC(f) drive |
| MILLIMETER PRODUCTS |
115A/599 |
WR28 Full Band Isolator, 25 dB isolation, 1.5 dB insertion loss |
| MILLIMETER PRODUCTS |
511A/599 |
WR28 Digital Readout Programmable Atten., 0-60 dB, GPIB |
| MILLIMETER PRODUCTS |
520A/599 |
WR28 Variable Attenuator, 0-25 dB, lockable vernier read drive, 1 Watt maximum |
| MILLIMETER PRODUCTS |
559A-03/599 |
WR28 Directional Coupler, 3 dB coupling |
| MILLIMETER PRODUCTS |
559A-10/599 |
WR28 Directional Coupler, 10 dB coupling |
| MILLIMETER PRODUCTS |
580A/600 |
WR28 Termination, 1 Watt max., 1.05 VSWR, choke flange |
| MILLITECH |
45351H-1320 |
WR28 (UG381/U round flange) Crossguide Coupler, 20 dB coupling. Split block construction |
| MILLITECH |
CL3-28-S1000 |
WR28 Directional Coupler, 10 dB coupling, split block |
| MILLITECH |
DRA-28-S0000 |
WR28 Precision Direct Reading Attenuator, 0-60 dB, 26.5-40 GHz |
| MILLITECH |
DRF-28-S0000 |
WR28 Direct Reading Frequency Meter, 26.5-40 GHz |
| MILLITECH |
JFD-28-SI1SF |
WR28 Full Band Junction Isolator, 20 dB isolation, insertion loss <1.2 dB, 26.5-40 GHz |
| MILLITECH |
JFD-28-WI |
WR28 Isolator, 20 dB, 33.5-36.0 GHz |
| MILLITECH |
MWS-28-1RGAW |
WR28 Motorized 3-Position 4-Port Switch & manual/GPIB controller |
| MILLITECH |
MXP-28-A010LS |
WR28 Balanced Mixer, RF/LO=26.5-40 GHz, LO=+13 dBm, IF=DC-13GHz |
| MILLITECH |
MXP-28-RFSFL |
WR28 Balanced Mixer, RF/LO=26.5-40 GHz, LO=+13 dBm, IF=DC-13 GHz |
| MILLITECH |
MXP-28-RSXSL |
WR28 Balanced Mixer, RF/LO=26.5-40 GHz, LO=+13 dBm, IF=DC-13 GHz |
| MILLITECH |
SWS-28-S01000 |
WR28 Straight Section, 1 inch length, gold flashed |
| MILLITECH |
SWS-28-S03000 |
WR28 Straight Section, 3 inches length, gold flashed |
| MITEQ |
WGWR28-KM |
WR28 x 2.92mm male End Launch Adapter |
| MPI |
1759 |
WR28 Straight Section, 1 inch length |
| MRI |
MIR-39 |
WR28 Isolator, 20 dB, 38-40 GHz |
| MRI |
MIR-39 (a) |
WR28 Isolator, 18 dB, 36-38 GHz, 0.5 inch length |
| MRI |
MIR-39 (b) |
WR28 Isolator, 18 dB, 38.2-39.4 GHz, 0.5 inch length |
| MRI |
MIR-39 (d) |
WR28 Isolator, 18 dB, 36-40 GHz |
| MRI |
MIR-39 © |
WR28 Isolator, 18 dB, 38.0-39.7 GHz, 0.5 inch length |
| MW. DEVELOPMENT CO. |
62028-001 |
WR28 Low Power Termination |
| MW. DEVELOPMENT CO. |
66028-1030 |
WR28 Straight Section, 1-1/4 inch length, aluminum |
| MW. DEVELOPMENT CO. |
76028-156 |
WR28 Fixed Attenuator, 20 dB |
| M-WAVE |
28CA5KF-1 |
WR28 x 2.92mm(f) Adapter |
| M-WAVE DESIGN |
28CA1244 |
WR28 x 2.92mm(f) Adapter, 1.30 VSWR |
| M-WAVE DESIGN |
28EB1202 |
WR28 90 degree E-Plane Mitre Bend, 2.5 inch bend radius |
| M-WAVE DESIGN |
28FA1224 |
WR28 Fixed Attenuator, 50 dB, 38-40 GHz, body length 6.1 inches, aluminum |
| M-WAVE DESIGN |
28FA1B(5) |
WR28 Fixed Attenuator, 5 dB, body length 1.25 inches, brass |
| M-WAVE DESIGN |
28SC-10 |
WR28 Directional Coupler, 10 dB coupling |
| M-WAVE DESIGN |
WR28 pickup horn |
WR28 Pickup Horn, 10 dBi gain, aluminum construction, 0.81 inch overall length |
| NARDA |
V1067-03 |
WR28 Directional Coupler, 3 dB coupling |
| NARDA |
V1067-10 |
WR28 Directional Coupler, 10 dB coupling |
| NARDA |
V357 |
WR28 90 degree Twist Section, 3 inches length |
| NARDA |
V377 |
WR28 Sliding Load, uncalibrated drive |
| NARDA |
V717-03 |
WR28 3 dB Fixed Attenuator |
| NARDA DBS MICROWAVE |
DB99-1164R2 |
WR28 Downconverter,RF=38-40 GHz, LO=12.7-14G +7 dBm, IF=10-2500M,6V |
| OMEGA LABS |
3311-J |
WR28 Directional Coupler, 40 dB coupling |
| omega labs |
WR28-WR42 |
WR28 x WR42 Taper Section, 2 inches length |
| OVERWAVE LABS |
WR28-Kf |
WR28 x 2.92mm(f) Adapter |
| PAMTECH |
RYG2031 |
WR28 Junction Isolator, 20 dB, 37-40 GHz |
| PENN ENGINEERING |
5030-111B-10 |
WR28 Directional Coupler, 10 dB coupling |
| PENN ENGINEERING |
WR28 H 90 |
WR28 90 degree H-Plane Bend, cover/choke flanges |
| PRD |
312-AF1 |
WR28 E-H Plane Tuner, micrometer drives |
| PRD |
A414-10F1 |
WR28 Directional Coupler, 10 dB coupling |
| QUASAR |
QFA22RQZ |
WR28 40 dB Fixed Attenuator (35 dB at 26.5G; 40 dB at 34G; 45 dB at 40G), 1 watt maximum |
| QUASAR |
R-112-15CM |
WR28 Straight Section, brass, 15cm (5.88 inches) length |
| QUASAR MICROWAVE |
QDC22-810960 |
WR28 Directional Coupler, 10 dB coupling |
| QUASAR MICROWAVE |
QFL22-EQB-443B |
WR28 Low Power Termination, 1.10 VSWR, 1 Watt max. |
| QUASAR MICROWAVE |
QPB22-CQZ442442C90E |
WR28 90 degree E-Plane Bend, brass |
| QUINSTAR |
QJG-A03300 |
WR28 Directional Coupler, 3 dB coupling, spli block construction |
| QUINSTAR |
QJR-2810-BA |
WR28 Directional Coupler, 10 dB coupling, split block construction |
| QUINSTAR |
QJR-2820-BA |
WR28 Directional Coupler, 20 dB coupling, split block construction |
| QUINSTAR |
QWZ-AM1500 |
WR28 Solenoid or Manual Driven DPDT Transfer Switch, 15 VDC with indicator lines |
| RADIALL |
R2791 |
WR28 Circulator, 18 dB isolation, 29-32 GHz |
| RADITEK |
RADI-37-40 |
WR28 Isolator, 25 dB, 37-40 GHz, 1/2 inch insertion length |
| RANTEC |
62640 |
WR28 Conical Horn, 1.65 inch length x 0.85 inch diameter, with 10.5 inchb diameter radome attached, feed optimized for 28 GHz |
| SCIENTIFIC ATLANTA |
14-7-1 |
WR28 Single-Ended Harmonic Mixer, 26.5-40 GHz, for 1780 receiver |
| SPACE KOM |
DFKa-U |
WR28 Downcoverter,13-20 GHz +20 dBm LO, IF=0.1-50 MHz,15V IF amp |
| SPACE MACHINE & ENG. |
60788-27 |
WR28 x 2.92mm(f) Adapter |
| SPACEK LABS |
28 GHz mixer |
WR28 Mixer, RF=27-30 GHz, internally doubled LO=13.5-15 GHz +17 dBm, amplified IF=1-500 MHz, 10 dB conversion gain, 12V 20mA |
| SPACEK LABS |
37.6-40G BPFL |
WR28 Band Pass Filter, 37.6-40 GHz, 5-section, 1.5 inch length |
| SPACEK LABS |
GKA-360 |
WR28 Fixed Tuned Gunn Oscillator, 36.43 GHz, +15 dBm Po,+4.5V 820mA, with attached MRI junction isolator |
| SPECTRM |
WA-R028-HF01 |
WR28 x 2.4mm(f) Adapter |
| SPERRY |
22V2 |
WR28 E-H Plane Tuner, micrometer drives |
| SPERRY |
23V1 |
WR28 Adjustable Short, micrometer read |
| SYSTRON DONNER |
110572 |
WR28 x WR42 Taper Section, 3 inches length |
| SYSTRON DONNER |
DBD-056 |
WR28 Choke to Choke Flange Adapter, 0.35 inch length |
| SYSTRON DONNER |
DBD-430 |
WR28 Variable Attenuator, 0-20 dB, 0-100 arbitrary dial scale |
| SYSTRON DONNER |
DBD-440A-10 |
WR28 10 dB Fixed Attenuator, 1 Watt maximum |
| SYSTRON DONNER |
DBD-450 |
WR28 Low Power Termination, 1/2 Watt maximum |
| SYSTRON DONNER |
DBD-620 |
WR28 H-Plane (Shunt) Tee |
| SYSTRON DONNER |
DBD-620-SP |
WR28 H-Plane (Shunt) Tee, choke fl's main line, cover fl. Tee |
| SYSTRON DONNER |
DBD-675-10 |
WR28 Directional Coupler, 10 dB coupling |
| SYSTRON DONNER |
DBD-675-3 |
WR28 Directional Coupler, 3 dB coupling |
| SYSTRON DONNER |
DBD-979-1 |
WR28 E-H Plane Tuner, micrometer read drives |
| TECHNICRAFT |
TS41-4-B-2.50-N |
WR28 Jacketed Flexible Section, 2.5 inches length, cover/choke, silver-brass |
| TEKTRONIX |
WM490A |
WR28 Harmonic Mixer, 26.5-40 GHz |
| TRAK MICROWAVE |
2571-1801 |
WR28 Isolator, 20 dB, 26.5-40 GHz, <1.5 dB ins. Loss |
| TRAK MICROWAVE |
2571-1810 |
WR28 Isolator, 20 dB, 26.5-40 GHz, <1.5 dB ins. Loss |
| TRG |
169A/599 |
WR28 Isolator, 20 dB, 34.3-36.6 GHz, 3/4 inch insertion length |
| TRG |
565A/599 |
WR28 3-Port Crossguide Coupler, 20 dB coupling, split block body, 1.5 inch insertion length |
| TRG |
580A/599 |
WR28 Termination, 1 Watt max., 1.05 VSWR |
| TRG |
640A/599 |
WR28 Series (E-Plane) Tee, 2.38 inches length |
| TRG |
650A/599 |
WR28 H-Plane (Shunt) Tee |
| TRG |
690A-3.00/599 |
WR28 Straight Section, 3 inches length |
| TRG |
861A/599 |
WR28 Standard Gain Horn, 24 dBi gain mid-band |
| TRG |
A510 |
WR28 Precision Direct Reading Attenuator, 0-50 dB |
| TRG |
A521-03 |
WR28 3 dB Fixed Attenuator, 1 Watt maximum |
| TRG |
A526 |
WR28 Variable Phase Shifter, 0-180 degrees, lockable dial drive, UG381/U flanges with UG599/U adapters- 4.75 inches length |
| TRG |
A551 |
WR28 Direct Reading Frequency Meter, 26.5-40 GHz |
| TRG |
A559-10 |
WR28 Directional Coupler, 10 dB coupling |
| TRG |
A585 |
WR28 Sliding Matched Load, micrometer drive |
| TRG |
A590 |
WR28 Adjustable Short, micrometer drive |
| TRG/ NEMS |
A521-01 |
WR28 1 dB Fixed Attenuator, 1 Watt maximum |
| UMT |
31 GHz BPFL |
WR28 Band Pass Filter, 31.000-31.075 GHz |
| UMT |
31.25 GHz BPFL |
WR28 Band Pass Filter, 31.225-31.3 GHz |
| UMT |
38.8 GHz BPFL |
WR28 Band Pass Filter, 38.6-38.95 GHz |
| UMT |
39.5 GHz BPFL |
WR28 Band Pass Filter, 39.3-39.65 GHz |
| UNIQUE BROADBAND |
152-28-20 |
WR28 Fixed Attenuator, 22 +/-3 dB, 2 inches length, brass |
| US ARMY |
C5U-83175 |
WR112 (proprietary flange) x WR28 (proprietary flange) Taper Section, 1.25x0.57 inch four hole flangepattern WR112 / 0.73x0.55 four hole flange pattern WR28, 1.95 inch length, aluminum |
| WATKINS JOHNSON |
2A6700N |
WR28 Mixer, 11-20 GHz +15 dBm LO, 100kHz-6 GHz IF, 15V bias |
| WAVELINE |
100310 |
WR28 (choke flange) Detector, negative polarity, BNC(f) |
| WAVELINE |
1005-A |
WR28 Direct Reading Variable Attenuator, 0-20 dB |
| WAVELINE |
1038 |
WR28 45 degree E-Plane Bend, cover/choke flanges |
| WAVELINE |
1038-1 |
WR28 45 degree E-Plane Bend, choke flanges |
| WAVELINE |
1039 |
WR28 45 degree H-Plane Bend, cover/choke flanges |
| WAVELINE |
1039-2 |
WR28 45 degree H-Plane Bend, cover flanges |
| WAVELINE |
1041-03 |
WR28 Straight Section, 3 inches length |
| WAVELINE |
1042-06 |
WR28 Straight Section, 6 inches length, cover/choke flanges |
| WAVELINE |
1042-1-06 |
WR28 Straight Section, 6 inches length, choke flanges |
| WAVELINE |
1049-4 |
WR28 Straight Section, 1.5 inch length |
| WAVELINE |
1067 |
WR28 Pressurization Section, two inlets, one with 0-15 PSI gage, 4 in. length |
| WAVELINE |
1070-20 |
WR28 3-port Crossguide Coupler, 20 dB coupling |
| WAVELINE |
1074-03 |
WR28 Directional Coupler, 3 dB coupling |
| WAVELINE |
1078-H |
WR28 4-Port Manual Transfer Switch, H-Plane switching |
| WAVELINE |
1083 |
WR28 E-H Plane Tuner, micrometer drives |
| WAVELINE |
1085 |
WR28 H-Plane (Shunt) Tee |
| WAVELINE |
1090 |
WR28 90 degree Twist Section, 3.5 inches length, cover/choke flanges |
| WAVELINE |
17-02137 |
WR28 Asymertric 90 deg. H Bend, 1-3/4" x 1-1/8" legs, choke fl's |
| WAVETRONICS |
6618S-01 |
WR28 Slide Screw Tuner, vernier read |
| WILTRON |
35WR28K |
WR28 x 2.92mm(m) Adapter |
| WILTRON |
35WR28KF |
WR28 x 2.92mm(f) Adapter |
