| MANUFACTURER |
MODEL |
DESCRIPTION |
| AILTECH |
7650-114 |
Noise Generator, 37.0 dB ENR, 379-441 MHz, N(m), 28 VDC |
| AILTECH |
7650-115 |
Noise Generator, 37.0 dB ENR, 28-32 MHz, N(m), 28 VDC |
| AILTECH / EATON |
7617 |
Noise Generator, 15.5 dB ENR, 12.4-18 GHz, SMA(f), 28 VDC |
| ALFORD MICROWAVE |
3161 |
TNC Calibration Kit, DC-18 GHz [m/f sliding loads, offset& flush shorts, terminations] |
| EATON/ AILTECH |
7660-147 |
Noise Source, 230-270 MHz, 35.5 dB ENR, SMA(f), 28VDC |
| EATON/AILTECH |
7650-055 |
Noise Source, 2.55-2.85 GHz, 15.5 dB ENR, N(m), 28VDC |
| FXR/MICROLAB |
HM-10N |
Signal Sampler, 10 dB coupling, DC-5 GHz, 2.5 dB ins.loss,Nm/f/f |
| GENERAL RADIO |
1442-F |
5 Ohm Resistance Standard, usable to 100 MHz, two GR900 ports |
| HP/KEYSIGHT |
08566-60003 |
Mixer Bias Protection Network, BNC(f/f) |
| HP/KEYSIGHT |
11665B |
Modulator, 0.15-18.0 GHz, N(m/f), for use with HP 8755/6/7 |
| HP/KEYSIGHT |
11853A |
50 Ohm type n Accessory Kit (one each 11511A/11512A N female/male short; two each N female/female and N male/male adapters) |
| HP/KEYSIGHT |
11855A |
75 Ohm Type N Accessory Kit (2 Nm/m, 2 Nf/f, 1 Nm termination, 1 Nm short, 1 Nf short) |
| HP/KEYSIGHT |
11866A |
APC7 Short/ Open/ Load Kit; load is 909C DC-2 GHz 1.005 VSWR |
| HP/KEYSIGHT |
35678A |
Type N Cal, Kit, c/o 1 each 909C-012,200, 909C-013,200, male&female shorts, N(m/m) & N(f/f) adapters |
| HP/KEYSIGHT |
5060-0370 |
APC7 Collet Extraction Tool |
| HP/KEYSIGHT |
5345A/55A/56D |
18 GHz Frequency Counter, extendes to 110 GHz with use of HP 11970 series mixers |
| HP/KEYSIGHT |
5352B-005,010 |
46 GHz Frequency Counter, ovenized reference option |
| HP/KEYSIGHT |
85027E |
Directional Bridge, 0.01-26.5 GHz, 3.5mm male test port, for 8756/7 series analyzers *bridge only - without accessories* |
| HP/KEYSIGHT |
85032B |
Type N Calibration Kit |
| HP/KEYSIGHT |
85032E |
Type N Economy Calibration Kit |
| HP/KEYSIGHT |
85050B |
7mm Calibration Kit, for HP 8510/ 8720 |
| HP/keysight |
85050C |
7mm Calibration Kit, for HP 8510/ 8720 |
| HP/KEYSIGHT |
85051A |
7mm Verification Kit, for HP 8510 |
| HP/KEYSIGHT |
85051B |
7mm Verification Kit, for HP 8510/8720 |
| HP/KEYSIGHT |
85130B |
Test Port Adapter Set, 3.5mm (test port) to 7mm |
| HP/KEYSIGHT |
8710-1766 |
APC7 Torque Wrench, 12 lb.-in. |
| MAURY MICROWAVE |
8780N-opt.01 |
OSP (male) Short/ Open/ Load Calibration Kit, DC-6 GHz *NEW* |
| MAURY MICROWAVE |
A028D2 |
7mm Master Gage, for 7mm VNA calibration kit |
| MAURY MICROWAVE |
MT-7118A |
Cryogenic Termination, DC-18 GHz, APC7 |
| MICRONETICS |
NOD-5107 |
Noise Generator, 100 Hz-100 MHz, +10 dBm max., 10 dB step atten. |
| NARDA |
466B |
Thermocouple Power Monitor Sensor, 10 MHz-12.4 GHz, 1-100mW, Nm |
| NARDA |
466B |
Power Monitor, 0.01-12.4 GHz, 1-100 mW, for Narda meter |
| NOISE COM |
NC-1107A |
Amplified Noise Module, 100 Hz-100 MHz, +13 dBm, -67 dBm/Hz, SMAf, 28VDC |
| OMNI-SPECTRA |
2598-5238-54 |
Set of two OSP gages: male pin & female pin |
| OMNI-SPECTRA |
2598-5239-54 |
Set of two OSSP gages: male pin & female pin |
| TEKTRONIX |
015-0385-00 |
External Mixer Diplexer, for Tektronix 490/2750 series spec.an. |
| TEKTRONIX |
CT-2 / P6041 |
Current Transformer, 1 millvolt per milliamp, into 50 Ohms |
| WILTRON |
3666 |
3.5mm Verification Kit: 360 disk; 19S50-7 3.5mm airline; 19S50-7B 3.5mm BEATTY AIRLINE; 42S-20 & 42S-50 20 dB & 50 dB DC-26.5 GHz attenuators |
| WILTRON |
6400-6N75 |
SWR Autotester, 1-1000 MHz, 75 Ohm N, 40 dB dir.,for 6400 series |
| WILTRON |
6400-6N75-1 |
SWR Autotester, 1-2000 MHz, 75 Ohm N, 38 dB dir.,for 6400 series |
