V5 Scanning Hipot / Electrical Safety Analyzer
Everything You Need In a Multi-point Safety Analyzer for an Exceptionally Low Price

The V5 Sets the Standard for Versatility and Value.

Only Vitrek, world leaders in electrical safety test automation, could build a feature rich, full function 5-in-1 electrical safety tester with performance this high and a price this low. The new Vitrek V5 combines AC Hipot to 5KV, DC Hipot to 6KV, insulation resistance to 10 gig-ohms and high current ground bond measurement up to 42 Amps and a built-in 8 channel HV Scanner. And all this comes in one systems ready, low profile, rugged, rack mount package – complete with rear terminal outputs.

 

Features/Benefits

• Built-in 8 Channel Scanner
• Tests AC, DC Hipot, IR & Ground Bond to UL, CSA, IEC & TUV Specs
• Up to 5KVAC 40mA
• Up to 6KVDC 10mA
• Multi-mode IR 50-1000V up to 10,000MΩ
• Ground Bond up to 42Amps
• Leakage current resolution down to 10μA
• Fully programmable RS232 optional GPIB interface
• Selectable arc detection
• Available Safety Fault Interrupt (SFI)™ circuit
• CE mark certified EN61010
• 10 position test sequence memory
• 3 year extended warranty

 

Top of Page


Specifications

AC Hipot

Voltage Range:	100 to 5000 VAC RMS
Voltage Setting Resolution:	5V/step
Voltage Regulation:	1% of reading + 5V
Voltage Accuracy:	1% of reading + 10V
Voltage Monitoring:	At Output Terminals
Output Current:	30mA to 40mA 180S max, 0 to 30mA continuous.  Below 500V 10mA max
Min/Max Current Limits:	0.1 to 40mA
Current Accuracy:	1% of reading + 50mA

Top of Page


DC Hipot

Voltage Range:	100 to 6000 VDC
Voltage Setting	Resolution: 5V/step
Voltage Regulation:	1% of reading + 5V
Voltage Accuracy:	1% of reading + 10V
Voltage Monitoring:	At Output Terminals
Max Output Current:	10mA continuous, below 500VDC 2mA continuous
Min/Max Current Limits:	0.01 to 10mA
Current Accuracy:	1% of reading + 50mA


Insulation Resistance

DC Output Voltage:	50, 100, 500 or 1000V
Resistance Range:	1 to 9999mW

Resistance  Accuracy: (% of reading)
50, 100 VDC	1-50MW 5% 51-200MW 10% 201-1999MW 20%
500, 1000 VDC	1-500MW 5% 501-2000MW 10% 2001-9999MW 20%

Multi-Mode IR™:

Select 1 of 3 modes - test passes on good reading, test fails on bad reading, pass/fail determined at end of test time.

Top of Page


Ground Bond/Continuity

Test Current:	3A to 42 Amps RMS
Terminal Configuration:	4 wire Kelvin
Resistance Range:	0 to 600mW
Resistance Resolution:	100mW
Resistance Accuracy:	1% reading ± 3mW
Compliance Voltage:	8 volts at terminals
Current Resolution:	0.01A
Voltage Resolution:	0.01V

Top of Page


General

Test Database:	10 test sequences with up to 16 steps per test sequence
Front Panel Lockout:	Prevents database edit while in lockout mode
Arc Detect:	10 level trip select
Remote Interfaces:	RS232 - Fully interactive PLC - Inputs; Start, Reset Outputs: Testing, Pass, Fail GPIB - Option GP-V5
Timer Accuracy:	0.25% ± 50mS
Power Source:	AC100v, 120V, 220V, 230V (±10% 50/60Hz), 350W max
Operating Environment:	Indoor use, altitude up to 6500 ft (2000m). Installation Category II. Pollution Degree 2.
Operating Temperature:	0°C to 40°C, 80% RH
Storage Temperature:	-10°C to 70°C, 70% RH
Dimension:	17 W x 17 D x 5.25 H, (432mm x 432mm x 133mm)
Weight:	39lbs (18kg) net, 45 lbs (20kg) ship
Accessories:	NIST Cal Cert, TL-20-60 & K-2 Test Leads, Instruction Manual and Power Cord.
Accuracy:	Stated specifications apply for 1 year at 23°C ± 5°C.
Calibration:	ANSI/NCSL Z540 Certificate of Calibration with Data traceable to NIST.
Compliance:	CE Mark Certified to EN61010 and EMC Directives EN50081-1 & EN50082-2.
Warranty:	3 Year Extended Warranty with registration and annual factory calibration, 1 year parts and labor standard.


QuickTest™ Software

Option QT-V5:

Bundled Test Automation Software and PC Serial Interface Cable.  Easy to load graphical test sequence development and operating environment. Provides time/date, operator, test parameters, test results and readings.  Results may be viewed, printed out or exported to a database program.