AILTECH |
230165-14 |
Noise Generator, 25+/-0.5 dB ENR, 12.4-18.0 GHz, SMA(f), +28 VDC |
AILTECH / EATON |
7617 |
Noise Generator, 15.5 dB ENR, 12.4-18 GHz, SMA(f), 28 VDC |
ANRITSU |
560-7N50B |
Detector, 10 MHz-20 GHz,N(m),for Anritsu/Wiltron netwk analyzers |
EIP |
548A-06,08,590 |
110 GHz Counter; 0-26.5 GHz 3.5mm & includes mixers 26.5-110 GHz |
FXR/MICROLAB |
HM-10N |
Signal Sampler, 10 dB coupling, DC-5 GHz, 2.5 dB ins.loss,Nm/f/f |
GENERAL RADIO |
1442-F |
5 Ohm Resistance Standard, usable to 100 MHz, two GR900 ports |
HP/AGILENT |
08566-60003 |
Mixer Bias Protection Network, BNC(f/f) |
HP/AGILENT |
11650A |
APC7 Calibration Kit, for HP 8410 series network analyzers |
HP/AGILENT |
11665B |
Modulator, 0.15-18.0 GHz, N(m/f), for use with HP 8755/6/7 |
HP/AGILENT |
11752E |
2.92mm/ 2.4mm Connector Gage |
HP/AGILENT |
11866A |
APC7 Short / Open / Load (909C) Calibration Kit, DC-2 GHz |
HP/AGILENT |
3048A-K21 |
AM Detector/ Filter, 1 Hz-40 MHz |
HP/AGILENT |
346C |
Noise Source, 14 dB ENR, 10 MHz-26.5 GHz, APC3.5(m), 28V |
HP/AGILENT |
35678B |
75 Ohm Type N Calibration Kit |
HP/AGILENT |
85021A |
Directional Bridge, 0.01-18 GHz, 40 dB Directivity,for HP 8756/7 |
HP/AGILENT |
85023A |
APC7 Verification Kit |
HP/AGILENT |
85023C |
Type N Verification Kit |
HP/AGILENT |
85027A |
Directional Bridge, 10 MHz-18 GHz, APC7 test port |
HP/AGILENT |
85050B |
7mm Calibration Kit, for HP 8510/ 8720 |
HP/AGILENT |
85050D |
7mm Economy Calibration Kit, for HP 8510/8720 |
HP/AGILENT |
85051B |
7mm Verification Kit, for HP 8510/8720 |
HP/AGILENT |
85130A |
3.5mm - 7mm Adapter Kit, for HP 8510/8720 |
HP/AGILENT |
85130B |
3.5mm - 7mm Adapter Kit, for HP 8510/8720 |
HP/AGILENT |
85320A |
2-26.5 GHz Test Mixer Module, for HP 85301 antenna range rcvr. |
HP/AGILENT |
85320B |
2-26.5 GHz Reference Mixer Module, for HP 85301 |
M/A-COM |
1560-1577 |
Connector Gage Kit, for SMA male & female center contact |
MAURY MICROWAVE |
8650E |
TNC Calibration Kit for HP 8510 Vector Network Analyzer |
MAURY MICROWAVE |
8650K |
TNC Calibration Kit for VNA, without calibration constants disk |
MAURY MICROWAVE |
8780N-opt.01 |
OSP (male) Short/ Open/ Load Calibration Kit, DC-6 GHz *NEW* |
MICRONETICS |
NOD-5107 |
Noise Generator, 100 Hz-100 MHz, +/-1.5 dB flatness, -70 dBm/Hz |
NOISE COM |
NC3404 |
Noise Source, 33 dB ENR, 2-4 GHz, SMA(f) output, 28VDC |
OMNI-SPECTRA |
2598-5238-54 |
Set of two OSP gages: male pin & female pin |
OMNI-SPECTRA |
2598-5239-54 |
Set of two OSSP gages: male pin & female pin |
P.T.S. |
250-R6N1X-6 |
BCD Programmable Synth.,1-250 MHz,1 Hz res.,ext.5/10 MHz ref.req |
TEKTRONIX |
015-0385-00 |
External Mixer Diplexer, for Tektronix 490/2750 series spec.an. |
TRIANGLE MICROWAVE |
FD-31-N |
Freq. Discriminator, 2.2-2.3 GHz, +14 dBm in, -20 to +20 mV out |
WILTRON |
01-222,223,210 |
Connector Guage Kit for WSMA connector (m&f), DC-26.5 GHz |
WILTRON |
5400-6N50 |
SWR Autotester, 1-3000 MHz, N(m), 40 dB dir., for 5400 series |
WILTRON |
560-97A50 |
SWR Autotester, 10 MHz-18 GHz, APC7 test port, for 560 series |
WILTRON |
560-98S50 |
SWR Autotester, 10 MHz-26.5 GHz, 3.5mm(m) test port, for 560 |
WILTRON |
6400-6N75 |
SWR Autotester, 1-1000 MHz, 75 Ohm N, 40 dB dir.,for 6400 series |
WILTRON |
6400-6N75-1 |
SWR Autotester, 1-2000 MHz, 75 Ohm N, 38 dB dir.,for 6400 series |
WILTRON |
75 Ohm S-O-L |
75 Ohm N(f) Calibration Kit c/o 26NF75 Load & 22NF75 Short/ Open |
